| WWV172.0 |
Fixed bugs and functions are improved. |
| WWV171.0 |
Fixed bugs and functions are improved. |
| WWV170.0 |
[Feature improvement]
1. Support for Epson Projector Professional Tool V1.60
Compatible with Camera Assist V200.
2. Change in Connection Specifications with ELPEC01
Before V160: Connection via rear USB port was only valid when using ELPLX02 lens.
After V170: Connection via rear USB port is valid even with lenses other than ELPLX02.
Target models: EB-PQ2220B, PQ2216B/W, PQ2213B
３．The specification for Remote Camera Access has been updated.
- The Remote Camera Access password has been deleted.
- When capturing via Remote Camera Access through Web Control, the confirmation process with the Remote Camera Access password has been removed.
- The default setting for Remote Camera Access in Password Protect has been changed to OFF.
４．Change in update frequency of information stored Inside the projector
[Bug fixes]
１．The settings file obtained from [Export EPMC Settings]* in the Web Control cannot not be applied by performing [Import EPMC Settings]** in the menu.
* Web Control: [Network] > [Export EPMC Settings]
** Menu: [EPMC Monitoring Control] > [Import EPMC Settings]
2. Fixed issue where Light Source Calibration / Refresh Mode options were sometimes greyed out on the Web Control schedule editing screen.
3. Fixed issue where the EPSON logo was not displayed correctly when screen type was set to "16:6" or "21:9".
4. Fixed issue where the blending range in Edge Blending could not be set correctly for screen types other than 16:9.
5. Fixed issue where supported SDI input signals were incorrectly recognized as unsupported.
6. Fixed issue where II error could occasionally occur during warmup. |
| WWV160.0 |
[Feature improvement]
1. Supports Epson Projector Management Connected V2.0
[Usability improvement]
1. Expand the lens shift range of supported lenses
For more information, contact your local EPSON support team.
2. Fan noise is reduced by optimizing the fan rotation speed in the following situations:
- Sleep Mode: ON
- No Signal
- No operation 5 min. or more.
[Bug fixes]
1. After performing the Blending Assist, if the assist result is not applied, the original geometric value might be initialized.
2. Image quality might not be as expected in the following situations:
- Frame interpolation is set to anything other than [Off]
- Projection is set to [Rear] or [Rear/Ceiling]
3. All Color Uniformity can not be adjusted in Web control if the adjustment level from 2 to 8 is not the same value.
4. When updating firmware with Wireless Mode off, power is still supplied to wireless even though Wireless Mode remains off.
5. Light Source Calibration may not reach the desired result
6. In Epson Projector Management Connected, if the proxy username includes "&", the export setting may fail.
|
| WWV151.0 |
[Bug fix]
Fix the following bugs
1. Fix for Screen Matching and Color Calibration issue
Performing [Screen Matching] or [Color Calibration] more than once could result in incorrect color uniformity correction.
2. Fix for Geometry Correction Issue via EPPT
The cursor might not display correctly when performing [Geometry Correction] using EPPT (Epson Projector Professional Tool).
3. Fix for Backup Source switching delay with 100Hz or 120Hz Signals
The [Backup Source] feature might take longer than usual to perform when inputting 100Hz or 120Hz signals.
4. Fix for Black Level values after Screen Matching
Some [Black Level] values might not be applied when selecting [Undo] or [Redo] after performing [Screen Matching].
5. Fix for HDMI Out Status Information
The status information of HDMI Out might not be displayed correctly in these scenarios.
- When switching HDCP from enabled to disabled on the source device
- When inputting an FRL signal |
| WWV150.0 |
[Feature improvement]
1. Support the Camera assist V150 of Epson Projector Professional Tool
- Add the mask feature for overshooting image with Camera assist*
- Improve UI
*: Blending assist / Stacking assist / Stacking and Blending assist
2. Unrestricted the following feature with 100V [Target model: EB-PQ2220B/PQ2216B/PQ2216W only]
- Light Source Calibration
- Estimated Remains (in Constant Brightness mode)
- Refresh mode
3. Specification change the following password settings
- Monitor password
If the following condition, display the dialog to set the Monitor Password
- Monitor Password: have not set
- Command Communication set to "Compatible"
- Web control password
If the following condition, display the dialog to promote to set Web Control Password
- Web Control Password: have not set
- Complete Network settings
[Yes]: Move to set the Web Control Password
[No]: Complete the Network settings with no set Web Control Password
4. Add the support signal format
- Support [Up to 4K 120Hz 40Gbps] (E.g. FullHD@100p/120p, 4K@100p/120p)
For details, please check the latest Specifications
- Add the [Up to 4K 120Hz 40Gbps] to the EDID menu.
[Bug fixes]
Fix the following bugs.
1. When adjusting lens shift with ELPLU03S, you can shift even over the displaying gage.
2. The value of Point correction (Vert.) and (Horiz.) are mistakes on Web control
3. When turning on the projector or changing the brightness, the YE warning may occur even though there are no problems with the light source etc.
4. Display the message that [the maximum limit of the adjustable brightness range has changed], even though attach the projection lens whom no limit.
5. [Blend Range] can be set even over the maximum value. |
| WWV101.0 |
[Feature improvement]
1. Changed the minimum magnification value of Scale Vertically and Horizontally from x0.50 to x0.75.
[Bug fixes]
1. Fixed a bug where the confirmation pattern for blending (curved surface) was cut off and displayed under the following conditions.
Conditions:
1) Set the screen type to anything other than "16:9"
2) Execute blending (curved surface) from EPPT (Epson Projector Professional Tool)
3) After success, select pattern display (for checking curved surface distortion)
2. Fixed a bug where the image would not display correctly when quickly changing the value of horizontal magnification in Scale settings.
3. Fixed a bug that could cause a PHW2 FN error when powering on the projector. |